How to configure the Toshiba ST-A10 to work with SellerDeck EPOS (With Toshiba...

[G.W.Green]

Please see below instructions to configure the Toshiba ST-A10 to work with SellerDeck EPOS.

If you find that the Toshiba printer, pole display or cash drawer stop working on the Toshiba ST-A10 for any reason, these instructions will show you how to configure the Toshiba ST-A10 from the beginning and solve the problem.

To configure the Printer and cash drawer in Epson OPOS:

1. Download the Toshiba printer drivers from the link below:
   
   http://www.sellerdeck.co.uk/support-...OSV001.008.zip
   
   
2. Unzip the file TRSTAxOPOSV001.008.zip onto your desktop.
3. Open the folder you just unzipped “TRSTAxOPOSV001.008”
4. Go into the folder “OPOS”, then double click on “TRST-A1x_OPOS_Installer_V001008.exe” to run it.
5. Click “Next”.
6. Select the radio button “Execute – Serial to USB Pos Printer and Cash Drawer”
   
   
   
   
   
   
7. Click “Next”.
8. Click “Install”, then "Finish".
9. Go to Start | Settings | Control Panel | Tec POS Drivers.
   
10. Click on little "+" sign next to "OPOS Control".
11. Click on little plus sign next to "POSPrinter"
    
    
    
    
    
12. Double Click on "TRSTA1S"
13. In this window, select the follow options:
    
    PrinterType = TRST-A0x
    Port = Com1
    Baud Rate = 9600
    Country = US
    Tick the tick box "Used Logical Name" and type "unit1" as the Logical Name.
    
    
    
    
    
    
14. Click “OK”
15. Click on little plus sign next to "CashDrawer"
    
    
    
    
    
16. Double click “DRWA1S”
    In this window, select the follow options:
    
    Port = Com 1
    Baud Rate = 9600
    Tick the tick box "Used Logical Name" and type "unit1" as the Logical Name.
    
    
    
    
    
    
17. Click “OK”

Your printer and cash drawer are now configured. To test they are working correctly, see instructions below:

1. Browse to the following location on your PC:
   
   C:\OPOS\TEC\TEST\
   
2. Double click on “OPOSCHK.exe”.
3. "TEC OPOS Interactive" now opens, you can now select a device, for example “TRSTA1S”, then click the “Feed” button, the printer will now testing feeding paper.
4. When you are finished testing, click "End".
   
   
   
   

To Configure the Pole Display / Customer Display

1. Go to Start | Control Panel | Add/remove programs.
2. Click on "OPOS Brugge", then click "remove", then select "yes" to unistall the program.
   
   
   
   
   
   
3. Restart you PC (Start | Shut down | Restart)
4. Now you need to reinstall the drivers.
   
   Double click on "My Computer", then browse to the following location:
   
   C:\Drivers\POSDRV\OPOS
   
5. Double click on "setup.exe"
6. Select "Next"
7. Select "Execute" and only have the tick box "ST-A10 Line display" ticked.
   
   
   
   
   
   
8. Click "Next", "Next again", then "Install", then finally "Finish".
9. Go to Start | Settings | Control Panel | Tec POS Drivers.
   
   
   
   
   
10. Click on little "+" sign next to "OPOS Control".
11. Click on little plus sign next to "LineDisplay"
    
    
    
    
    
12. Double Click on "LIUST51"
13. In this window, select the follow options:
    
    Port = Com 4
    Country = US
    Baud Rate = 9600
    Tick the tick box "Used Logical Name" and type "unit1" as the Logical Name.
    
    
    
14. Click "OK", then "OK" to close the program.
15. In SellerDeck EPOS, go to Setup | This till | "Printing" tab, and make sure the tick boxes "Epson OPOS avalible" and "Customer Display Active" is ticked and a message has been entered in "Customer Display Message".
16. The customer display is now fully configured. To test it, open SellerDeck EPOS, go to the sales screen, and press the "lock" button. This should make the customer display now show a your message